Programmers

The CH340 programmer and converter allows direct connection of ESP-01 and ESP-01s modules to a computer. The device provides stable UART serial communication and automatic code upload without additional hardware modifications. The integrated RESET button makes it easy to quickly restart the microcontroller. The module is indispensable when programming, testing ESP8266 circuits, and prototyping IoT systems. The exposed pins also allow convenient connection of external diagnostic tools, such as a logic analyzer.

Compact ESP8266 adapter for ESP-01 and ESP-01S modules. Features a built-in voltage regulator for safe powering in the 3.3V - 5V range. Standard 2.54 mm pin pitch and TX, RX, VCC, and GND pins make for quick breadboard assembly.

The module is ideal for Internet of Things (IoT) projects, adding Wi-Fi to Arduino or to Raspberry Pi. It enables stable circuit prototyping and remote control without risking damage to delicate components.

The EZP2019+ programmer kit is a universal USB tool for EEPROM and 24, 25 and 93 series FLASH memory. The device communicates via SPI and I2C interfaces and supports chips powered at 5V, 3.3V and 1.8V.

The included clip allows programming memory directly on the board, saving significant time. The hardware features automatic memory type recognition. It is ideal for BIOS repair, automotive controllers, instrument clusters, and microcontroller projects.

The EZP2019+ programmer is an advanced version of the EZP20xx series, offering support for a wider range of circuits. Equipped with a USB 2.0 interface, it provides an impressive data transfer rate of up to 12Mbps. An example of efficiency is the EN25T80's ability to read 8-Mbit memory in just 3 seconds and write in 9 seconds. This versatile programmer is used for home appliance repair, flashing TVs, DVD players, computer motherboards, as well as hard disk storage chips and other similar applications. Two SO8/SO16 adapters are included, making it easy to work with a variety of chips.

A compact USB CH340G RS232 TTL UART converter for reliable data transmission over the serial port. The module has 6 pins-including RX, TX, and GND-and LEDs that indicate operation. It supports 3.3V and 5V supplies. The device works well as a programmer for microcontrollers such as Arduino, ESP8266, ESP32, or Raspberry Pi. It is widely used for diagnosing network devices, prototyping electronic circuits, and communicating with external modules that require a UART interface.

The compact 8-channel Saleae 24 MHz logic analyzer is a professional tool for working with ARM, AVR, Arduino, or Raspberry Pi microcontrollers. USB-powered, it enables precise signal recording and hardware decoding of communication protocols such as I2C, SPI, 1-Wire, CAN, and I2S.

The analyzer has 8 independent logic inputs with 100K Ohm impedance. It excels at diagnosing communication errors with digital sensors and analysing data transfer in embedded systems.

CH341A programmer with a ZIF-16 socket is a versatile device for programming SPI Flash chips from the 25xx series and I2C EEPROM from the 24Cxxx series. The device is powered via USB 5 V and has a practical jumper for selecting the operating mode. It enables secure mounting without soldering. The module works well for recovering BIOS firmware, repairing consumer electronics and home appliances, updating routers, and in microcontroller projects. The kit includes an additional adapter for chips.

The ESP-01 and ESP-01S programmer module with CH340 is a device for convenient programming and data transfer between the computer and the ESP-01 and ESP-01S modules. It features a built-in 3.3V voltage stabiliser. The adapter is based on the popular CH340 chip. It allows direct connection of the WiFi ESP-01 and ESP-01S network modules to the USB port, allowing programming and data transfer from a PC.

USB to RS485 adapter with the CH340 chip is a professional tool for communicating devices using the Modbus, Profibus, and PLC standards with a computer. The converter supports the USB 2.0 interface and works with convenient Plug & Play technology without requiring additional power. It provides stable data transmission at speeds up to 6 Mbps over distances up to 1200 m. The product is ideal for industrial automation, machine diagnostics, and integration with popular microcontrollers and measurement systems.

ST-Link V2 Programmer is a versatile tool for programming and debugging STM32 and STM8 microcontrollers based on the ARM Cortex architecture. The device provides stable communication via SWD and SWIM interfaces, making it ideal for prototyping and testing embedded systems.

The hardware works with popular development environments such as ST-LINK Utility and KEIL RVMDK. The kit includes 4 female-to-female jumper wires for easier connection. The programmer supplies power to the target at 3.3V and 50mA.